遥控卷帘门具有的显着特点就是快速，这种快速就是体现在其卷帘门的技术含量上，那么，对于卷帘门的使用我们应该注意其特点，这样才能让卷帘门得到更好的使用。下面来讲讲吧。

The remarkable characteristic of remote control rolling shutter door is fast. This speed is first reflected in the technical content of the rolling shutter door. Then, we should pay attention to its characteristics for the use of rolling shutter door, so that the rolling shutter door can be better used. Now let's talk about it.

遥控卷帘门安装所需要用到的工具和过程

Tools and processes required for the installation of remote control roller shutter door

遥控卷帘门在我们的生活中被广泛适用于医药，仓库，物流，冷冻品等地方使用，主要起到了防尘，防水，隔热隔冷，防虫，防沙灰尘等主要特性。那么，对于遥控卷帘门安装所需要用到的工具和过程是怎样的呢？

Remote control rolling shutter door is widely used in medicine, warehouse, logistics, frozen goods and other places in our life. It mainly has the main characteristics of dust prevention, waterproof, heat insulation, cold insulation, insect prevention, sand and dust prevention. Then, what are the tools and processes required for the installation of remote control roller shutter doors?

1、必要工具

1. Necessary tools

角磨机、手枪钻、水平仪、冲击钻，拖线板，转头螺丝，螺丝刀、锤子，扳手，脚手架等等。

Angle grinder, pistol drill, level gauge, impact drill, drag line board, swivel screw, screwdriver, hammer, wrench, scaffold, etc.

2、主材料

2. Main material

门帘、导轨、轴承、编码器，红外对照，箱罩等主要部分组成。

Door curtain, guide rail, bearing, encoder, infrared contrast, box cover and other main parts.

3、辅助硬件

3. Auxiliary hardware

安装的必要条件，电源220v，洞口平整等。

Necessary conditions for installation, power supply 220V, hole leveling, etc.

4、出厂前的检查

4. Pre delivery inspection

对遥控卷帘门进行拆包检查，查看产品是否有漏件，核对产品出厂单，并开始着手安装。

Unpack and check the remote control roller shutter door to see if there are any missing parts, check the product delivery order, and start the installation.

作业条件

Operating conditions

1、结构工程施工完毕，粗装修之后、细装修之前，好墙面底子灰已完成，面层灰尚未施工前。

1. After the construction of structural works, after the rough decoration and before the fine decoration, the bottom ash of the wall has been completed, and the surface ash has not been constructed.

2、洞口尺寸及埋件位置、数量、规格符合设计要求。

2. The size of the opening and the position, quantity and specification of the embedded parts meet the design requirements.

3、进场产品验收合格。各部分相互匹配，配件齐全。

3. The mobilized products have passed the acceptance. Each part is matched with each other, and the accessories are complete.

安装导轨

Install the guide rail

将两则导轨按线焊牢于墙体预埋件上，施焊前注意吊垂直线检查导轨安装部位墙体垂直度，达不到垂直度要求时须加垫铁调垂直后方可施焊。

Weld the two guide rails on the embedded parts of the wall according to the line. Before welding, pay attention to hanging the straight line to check the verticality of the wall where the guide rail is installed. If the verticality requirement is not met, add a sizing block to adjust the verticality before welding.

调试

debugging

济南卷帘门厂认为要观察检查卷筒体、帘板、导轨和传动部分相互之间的吻合接触状况及活动间隙的匀称性，然后用手缓慢向下拉动关闭，再缓慢匀速向上拉提到位，反复几次，发现有阻滞顿卡或异常噪音时仔细检查产生原因后进行调整，直提拉顺畅，用力匀称为。对电控卷帘门，手动调试后再用电动机启闭数次，细听有无异常声音。

Jinan rolling shutter factory believes that it is necessary to observe and check the contact condition between the drum body, curtain plate, guide rail and transmission part and the symmetry of the movable gap, then pull it down slowly and close it by hand, and then pull it up slowly and evenly to the right place. Repeat it for several times. If there is blocking, jamming or abnormal noise, carefully check the cause and adjust it until the lifting is smooth and the force is even. For the electrically controlled roller shutter door, after manual debugging, use the motor to open and close it several times, and listen carefully for abnormal sound.

卷帘门安装过程中注意保护洞口周边装饰层。安装后洞口周边修补抹灰或装饰罩面时飞溅到卷帘门上的灰浆须及时用湿棉砂擦净。更多相关注意事项您可以关注我们网站http://www.jnzxmy.com获取到。

During the installation of roller shutter door, pay attention to protect the decorative layer around the hole. After installation, when repairing the plastering or decorative cover around the hole, the mortar splashed on the roller shutter door must be wiped off in time with wet cotton sand. For more relevant precautions, you can follow our website http://www.jnzxmy.com Get.