Before the installation of doors and windows, the door and window frames of different specifications should be moved to the corresponding holes and placed vertically. If it is found that the protective film falls off, the protective film should be subsidized, because the protective film is the last protection of the rolling shutter door, and it is difficult to protect the doors and windows without the protective film.

在安装将窗框放入洞口，使其上下框中线应与洞口上的安装中线对齐，并在框的四周及中蜒处用水模或垫块塞紧作临时固定，然后按设计困纸要求确定窗框在洞口罐体厚度方向的安装位置，以及安装高度，并慢慢地进行调整。

During installation, put the window frame into the hole so that the center line of the upper and lower frames is aligned with the installation center line of the hole, and plug the frame around and in the middle with water mold or cushion block for temporary fixation, then determine the installation position and installation height of the window frame in the thickness direction of the tank body at the hole according to the design requirements, and adjust it slowly.

调整的方法就是高度人或拉出垫在框与精体之间的木模，使窗框抬高或降低，以达到所需的位置。

The method of adjustment is to raise or lower the window frame by pulling out the wooden mold between the frame and the body, so as to reach the required position.

在将窗框调整到位后，先固定两点，应选窗框的两对角点行固定，然后再次对窗框的垂直度、水平度及直角度进行调整，使其偏差小于规定的要求后，再将其他螺钉分别固定牢固即可。

After the window frame is adjusted in place, two points shall be fixed first, and the two diagonal points of the window frame shall be fixed first, and then the perpendicularity, levelness and right angle of the window frame shall be adjusted again, so that the deviation is less than the specified requirements, and then other screws shall be fixed firmly.

门的安装与窗的安装各有不同，门的安装应在地面装饰工程施工前进行。应根据设计图纸及门扇的开启方向，确定门框的安装位置，并把门装入洞口，安装时应采取防止门框变形的措施，无下框平开门应使竖框的下边低于地面标高线，其高度差应不小子30mm。

The installation of door is different from that of window. The installation of door should be carried out before the construction of ground decoration engineering. The installation position of the door frame shall be determined according to the design drawings and the opening direction of the door leaf, and the door shall be installed into the hole. During the installation, measures shall be taken to prevent the deformation of the door frame. For the flat door without lower frame, the lower edge of the vertical frame shall be lower than the ground elevation, and the height difference shall not be less than 30mm.

也即竖框应少理入地停以下30mm。而带下框的平开门或维拉门应使下框低于地商标高线，其高度差宜为10mm，也即横下框应少埋入地坪以下10mm。

That is to say, the vertical frame should be at least 30mm below the ground stop. For the side hung door or sliding door with lower frame, the lower frame should be lower than the elevation of the ground mark, and the height difference should be 10 mm, that is, the horizontal lower frame should be buried at least 10 mm below the ground level.

然后，将上框的一个国定片固定在精体上，并用木模临时定位，同时调整门框的水平度、垂直度和直角度，当所有尺寸都到位后，就将所有的固定螺钉全部固定到位。

Then, fix a national fixed piece of the upper frame on the fine body, and use the wood mold to temporarily position it. At the same time, adjust the levelness, perpendicularity and right angle of the door frame. When all the dimensions are in place, fix all the fixing screws in place.

当安装连窗门时，门与窗应采用拼撞料拼簇，饼橙料下峭应固定在窗台上。

When installing the door with windows, the doors and windows should be made of colliding materials, and the orange cake material should be fixed on the windowsill.